› Comparison of Superplastic Forming Abilities of As-cast AZ91 Mg Alloy Prepared by Twin Roll Casting and WE43 Alloy - Vit Janik, WMG - University of Warwick
15:00-15:30 (30min)
› Two-dimensional grain boundary sliding and strain rate effect on dislocation characteristics in ODS ferritic steel - Hiroshi Masuda, Institute of Space and Astronautical Science, Japan Aerospace Exploration Agency, The University of Tokyo [Toyo]
15:30-16:00 (30min)
› A comparative study assessing the wear behaviour of different ceramic die materials during superplastic forming - Ares A. Gomez-Gallegos, Advance Forming Research Centre, University of Strathclyde
16:30-17:00 (30min)
› A method for the systematic assessment of lubricant performance during superplastic sheet forming - Marta Drabek, Advanced Forming Research Centre, University of Strathclyde
17:00-17:30 (30min)
› Protective coatings for superplastic forming ceramic dies: An initial study on protective coatings performance - Andrea Staiano, University of Strathclyde
17:30-18:00 (30min)
› Using the Particle Swarm Optimization Method for the Constitutive Modelling of AZ31B - Firas Jarrar, The Petroleum Institute
09:00-09:30 (30min)
› Mechanical behavior of Ti-6Al-4V titanium alloy with microstructural evolution modeling under hot and superplastic forming conditions - Marcio Santos, Institut Clément Ader, Polytechnic School of the University of São Paulo (Brazil)
09:30-10:00 (30min)
› FE-based optimization of the preform geometry for the superplastic forming of a spherical tank - Donato Sorgente, Università degli Studi della Basilicata [Potenza]
10:00-10:30 (30min)
› Aluminium alloys grain refinement and superplasticity - Anton Kotov, National University of Science and Technology "MISIS"
11:00-11:30 (30min)
› In-Situ EBSD Analysis & Characterisation of Nickel Additions to a Medium Strength 7000 Series Alloy - Scott Taylor, WMG - University of Warwick
11:30-12:00 (30min)
› On the Formability of AA6061/SiCp Composite Synthesized Using Friction Stir Processing - Viswanathan D, Professor (Retd.), Department of Mechanical Engineering, Anna University - Padmanabhan K.A, Professor of Eminence, Department of Mechanical Engineering, Anna University
12:00-12:30 (30min)
› Numerical and experimental integration in analysis of a superplastic forming - Carunchio Andre, IPT Instituto de Pesquisas Tecnológicas (Brazil)
14:00-14:30 (30min)
› Development of a strain dependent pressure law for superplastic forming of 2024 aluminium alloy - Rou DU, Laboratoire Angevin de Mécanique, Procédés et innovAtion
14:30-15:00 (30min)
› Superplastic forming optimization technique based on average strain rate controlling – Numerical simulation and experimental validation - Maxime ROLLIN, AIRBUS Operations Ltd., Ecole nationale supérieure des Mines d'Albi‐Carmaux
15:00-15:30 (30min)
› Low-temperature superplastic forming and diffusion bonding technology - Rinat Safiullin, Institute for Metals Superplasticity Problems Russian Academy of Sciences
16:00-16:30 (30min)
› Press development for superplastic forming with in situ and real time pressure and temperature control system and module with digital image correlation for strain monitoring. - Gilmar Bathala, Universidade de São Paulo
16:30-17:00 (30min)
› An industrialization case of superplastic forming by using Infra-Red heater - Marion Le Fournier, Aurock
17:00-17:30 (30min)
Industrial Applications: advanced forming processes I
room ALTAIR
Richard DASHWOOD
› From SPF to Hotforming of Aluminium Sheets – Simulation & Modelling Challenges between Industry and Academia - Rajab Said, ESI Group
09:30-10:00 (30min)
› Comparison of technical and commercial aspects regarding cold forming, SPF and hot stamping - W. Beck, FormTech GmbH
10:00-10:30 (30min)
Industrial Applications: advanced forming processes II
room ALTAIR
Werner BECK
› Hot Forming 2.0: Hydraulic Press for Hot Deep Drawing of Titanium - Hilko Siebels, Schuler Pressen GmbH
11:00-11:30 (30min)
› Hot & Cold Forming of industrial parts: A comparative study between aeronautical & automotive industries. How to improve collaboration with a die maker ? - Michel Garson, Loire Etude
11:30-12:00 (30min)
room ALTAIR
https://eurospf2016.sciencesconf.org/data/program/occ.jpg
